- Home
- Downdraft & Ventilated Autopsy Tables (Pedestal, Elevating & Bariatric)
USPE Autopsy Systems · OSHA-Compliant Downdraft, Hydraulic & Bariatric Tables
Downdraft & Ventilated Autopsy Tables (Pedestal, Elevating & Bariatric)
Factory-direct institutional equipment engineered with Type 304 and 316L stainless steel, verified MEP rough-in drawings, published pricing where available, and purchase-order and bid support for hospitals, medical examiners, universities, and forensic laboratories.
Featured Autopsy Tables | Morgue Tables | Mortuary Examination Tables
View all 12 models →
Related Elevating & Hydraulic Autopsy Tables
View all 2 models →
OSHA-Compliant Downdraft, Hydraulic Elevating & Pedestal Autopsy Tables
Autopsy table selection drives every utility rough-in in a pathology or forensic room: floor drain placement, hot/cold mixing valves, 115V/20A GFCI circuits, and dedicated exhaust ductwork. USPE engineers heavy-gauge Type 304 and Type 316L stainless steel autopsy tables across pedestal, dual-pedestal, L-shaped, mobile cart, hydraulic elevating, and bariatric configurations—built to hold breathing-zone formaldehyde concentrations well below OSHA 29 CFR 1910.1048 limits (0.75 ppm 8-hour PEL / 2.0 ppm 15-minute STEL).
Autopsy Table Architecture & Engineering Spec Comparison
| Table Style | Primary Application | Exhaust & Airflow | Load & Ergonomics | Explore Models |
|---|---|---|---|---|
| Center-Pedestal Downdraft Table | Hospital morgues, county ME offices | Integrated perimeter perforated grid panels; 275–450 CFM ducted downdraft | 600–1,000 lb static capacity; 360° clinician access | Autopsy Tables Catalog |
| Hydraulic / Electric Elevating Autopsy Table | Multi-pathologist suites, high-volume ME centers | Downdraft or back-draft plenum with flexible sealed exhaust boot | 30–40 in. powered vertical travel; reduces back strain during long procedures | Elevating & Hydraulic Tables |
| L-Shaped Autopsy & Dissection Station | Forensic & teaching suites needing dual work zones | Dedicated perimeter downdraft across both dissection and sink wings | Integrated organ dissection deck, hydro-aspirator, and heavy-duty disposer | Autopsy Table with Sink |
| Mobile Autopsy Table Cart / Transfer System | Small hospitals, coroners, cooler-to-table zero-lift workflow | Pairs with wall-mounted back-draft exhaust hood or wet-wall manifold | Locking 6–8 in. stainless casters; mates directly to cooler roller racks | Autopsy Table Carts |
| Bariatric Autopsy Table (36 in.+ Deck) | High-weight forensic and hospital cases | High-volume downdraft capture across wide-deck perforated trays | Reinforced 14 Ga 304/316 SS frame rated up to 1,000–1,200 lb | Bariatric Autopsy Tables |
Key Engineering Details Architects & Pathologists Check First
- Type 304 vs. Type 316L Stainless Steel: Standard autopsy tables use 14–16 gauge Type 304 stainless steel with #4 satin finish and continuously TIG-welded, coved internal corners. Facilities performing heavy formalin fixation, bleached washdowns, or corrosive chemical procedures should specify Type 316L molybdenum-alloy stainless steel for superior pitting resistance.
- Integrated Plumbing & Utility Pedestal: Specify vacuum-breaker protected hot/cold wrist-blade or knee-operated mixing faucets, concealed rinse-hose reels, heavy-duty 1/2 HP to 1 HP commercial garbage disposals, and hydro-aspirators with backflow prevention to satisfy local plumbing codes.
- Source-Capture Ventilation Verification: Downdraft autopsy tables pull formalin vapors and bioaerosols downward through removable stainless grid plates and out the pedestal base into dedicated single-pass building exhaust (typically 6–10 in. round or rectangular stub-up), keeping clean supply air moving over the pathologist's shoulders rather than across the face.
Autopsy Table Technical Guides & Side-by-Side Comparisons
- OSHA Formaldehyde Compliance for Autopsy Tables — 0.75 ppm PEL, 2.0 ppm STEL, and commissioning face-velocity verification.
- USPE vs. Mopec Autopsy Tables — gauge, plumbing, exhaust, lead-time, and factory-direct cost breakdown.
- Autopsy Table vs. Pathology Grossing Station — when a room needs both systems and how utilities differ.
- Autopsy Table RFQ Checklist — exact dimensions, drain specs, and electrical callouts for contractor submittals.
Frequently Asked Questions
How much exhaust CFM does a downdraft autopsy table require?
Most standard 30-to-36-inch wide downdraft autopsy tables require between 275 and 500 CFM of dedicated, single-pass building exhaust depending on deck area and static pressure. Always verify exact stub-up dimensions and static pressure drop on the model's USPE rough-in drawing before pouring floor slabs.
Should I choose Type 304 or Type 316 stainless steel for an autopsy table?
Type 304 stainless steel (14 to 16 gauge) handles daily clinical and forensic washdowns reliably. Upgrade to Type 316L stainless steel when your suite uses high-concentration formalin, chlorine bleach disinfectants, or saline preservatives regularly, as molybdenum alloy content resists pitting corrosion.
What is the advantage of a hydraulic elevating autopsy table over a fixed pedestal?
A hydraulic or electromechanical elevating autopsy table adjusts work height smoothly (typically 30 to 40 inches) for pathologists of different heights and allows flush docking with hydraulic cadaver transfer lifts, eliminating manual lifting.
Need room drawings, rough-in specs, or a consolidated USPE quote?
Send your floor plan or equipment schedule to our institutional spec desk for factory-direct pricing and CAD submittals.
Explore the Full USPE Pathology & Autopsy Equipment Network
Back to USPE Home →Autopsy & Forensic Pathology
- Forensic Pathology & ME Solutions Hub
- Downdraft & Ventilated Autopsy Tables
- All Autopsy Tables (Catalog)
- Elevating & Hydraulic Autopsy Tables
- Autopsy Table Carts & Mobile Tables
- Bariatric Autopsy Tables
- Autopsy Table with Integrated Sink
- OSHA Formaldehyde Compliance Guide
- USPE vs Mopec Autopsy Table Comparison
- Medical Examiner Facility Design Guide
Grossing, Anatomy & Histology Labs
- Pathology Grossing & Digital Pathology Hub
- Pathology Grossing Stations (Catalog)
- Elevating & Automated Grossing Stations
- Autopsy Table vs Grossing Station
- Anatomy Lab Dissection & Immersion Hub
- Cadaver Dissection Tables (Catalog)
- Cadaver Immersion & Dip Tanks
- Cadaver Immersion & Dip Tank Guide
- Anatomic Pathology, Histology, Saws & Scales
- Pathology Fume Hoods & Exhaust
Casework, Sinks, Cold Storage & Planning
- Stainless Steel Lab Casework Hub
- Stainless Steel Casework (Catalog)
- Autopsy & Pathology Scrub Sinks
- Autopsy & Dissection Sinks (Catalog)
- Morgue & Lab Refrigeration Hub
- Multi-Bay Vault Morgue Coolers
- Cadaver Storage Racks & Roller Systems
- Autopsy Table & Suite RFQ Checklist
- Government & County Bid Procurement
- USPE PET Veterinary & Necropsy Hub
Planning an autopsy suite, grossing room, or anatomy lab?
Send your room layout, equipment schedule, or bid specification for a consolidated USPE quote with MEP rough-in submittals.
Project photographs
Installed stainless steel casework
Sink cabinets, open knee space and glass-front storage, photographed in the room.








