U.S. Pathology Equipment

Autopsy Tables for Hospitals, Morgues & Medical Examiners

Choose an autopsy table for the examination, the room and the transfer route. Compare elevating and hydraulic autopsy tables, autopsy sink stations and anatomy and dissection tables, then bring the required equipment together in one facility RFQ.

Compare fixed-height sink tables with elevating and rotating pedestal equipment. Review the base model and its drawing, then request the configuration your room needs. For a larger project, explore the USPE pathology equipment range and include supporting equipment in the same request.

USPE adjustable-height pedestal autopsy table, base model Explore the adjustable-height pedestal table

Autopsy table guide · Updated November 2026

What is an autopsy table?

An autopsy table, also called a morgue table, post-mortem table or dissection table, is a stainless steel workstation used in hospital morgues, medical examiner and coroner offices, forensic laboratories and anatomy programs to support, examine and dissect human remains. USPE autopsy tables are fabricated from 304 stainless steel with radiused corners, a sloped or perforated working surface that drains to an integrated sink or end drain, and connections for hot and cold water, a hand spray rinse, hydro-aspirator and optional downdraft ventilation.

Material
Type 304 stainless steel (316L on request), welded and polished, radiused inside corners for sanitary cleaning.
Drainage
Sloped or perforated top draining to a center or end sink; waste outlet with trap and optional disposer or hydro-aspirator.
Ventilation
Downdraft or backdraft grilles pull formalin vapor and aerosols below the breathing zone; exhaust is matched to the building.
Bases
Fixed-height four- or six-leg tables, single central pedestal columns with 180° rotation, and electric or hydraulic elevating models.
Utilities
Hot/cold mixing faucet, hand spray, GFCI electrical outlets, lighting and instrument shelves specified per model.
Typical size
84 to 104 inches long, 30 to 36 inches wide, 34½ to 46½-inch working height on elevating models.

Autopsy table questions buyers ask

What is an autopsy table?

An autopsy table is a stainless steel work surface built to support a body during a post-mortem examination. It drains fluids to an integrated sink or end drain, supplies hot and cold water and a hand rinse, and can include downdraft ventilation, a hydro-aspirator, electrical outlets and a rotating or height-adjusting base. Autopsy tables are used in hospital morgues, medical examiner and coroner offices, forensic laboratories and anatomy programs.

What are the tables called in a morgue?

Tables used in a morgue are called autopsy tables, post-mortem tables, morgue tables or dissection tables. A rolling table used to move a body is an autopsy trolley, cadaver carrier or morgue cart, and a table used for preparation in a funeral home is an embalming table.

What is an autopsy table made of?

USPE autopsy tables are fabricated from Type 304 stainless steel with welded seams, a polished finish and radiused inside corners so the surface can be washed and disinfected quickly. Type 316L stainless can be quoted where chloride or disinfectant exposure requires it.

How big is an autopsy table?

USPE base models run 84 to 104 inches long and 32 to 36 inches wide. The fixed-height sink tables stand 36 inches high; the elevating pedestal table adjusts from 34½ to 46½ inches. Custom lengths, bariatric widths and pediatric configurations are quoted against the room plan.

Does an autopsy table need ventilation?

Formalin and biological aerosols should be controlled at the table. A downdraft autopsy table pulls air through grilles beside the working surface and exhausts it through the building system or a filtered unit; the facility engineer confirms airflow, duct route and make-up air. Fixed sink tables can be paired with room exhaust or a separate downdraft grossing station.

What is the difference between an autopsy table and an embalming table?

Both are stainless steel and drain fluids, but an autopsy table is built for dissection with a deeper working basin, hydro-aspirator, instrument space and optional downdraft exhaust, while an embalming table is a lighter, often height-adjustable preparation table used in funeral homes. American Mortuary Coolers supplies both lines.

Who buys autopsy tables and how are they purchased?

Hospitals, county medical examiners and coroners, state crime laboratories, universities and veterinary diagnostic labs buy autopsy tables by written quote, purchase order or formal bid. USPE equipment is quote-only: request pricing with the model, quantity and ship-to address and the quote returns with specification sheets, NAICS, UNSPSC and PSC references for your procurement file.

Content reviewed by the USPE fabrication team, Johnson City, Tennessee. Last updated November 22, 2026.

Plan the complete autopsy workflow.

Choose the table configuration before the accessories.

Pedestal and elevating tables

A rotating pedestal autopsy table provides a central support rather than a mobile carrier base. Compare the elevating USPE-AT-PED-E with the non-elevating USPE-AT-PED-N. Allow for the full rotation envelope and access to the sink, controls and services. Height adjustment alone is not a claim of ADA compliance.

Tables with a sink

Compare the 84-inch autopsy table with sink with the integrated-sink autopsy table. Identify the basin, drainage route, water services and included fittings in the model specifications. Disposers, rinse systems and electrical accessories must be included in the accepted scope, not assumed from a photograph.

Compare the current USPE autopsy table models.

These dimensions describe the listed base models. Start with the working surface and room layout; confirm changes, included fixtures and installation requirements on the accepted quote and drawing.

Base-model dimensions and configuration
ModelWorking layoutKey dimensionsNext step
USPE-AT-PEDRotating pedestal; elevating E or non-elevating N configuration; downdraft ventilation104 × 32-inch top. Elevating model: 34½–46½-inch working height. Non-elevating height set to order.Request pedestal table pricing
USPE-AT-84SFixed-height, four-leg table with integrated end sink84 × 36 × 36 inches overall; 16 × 20 × 8-inch sink.Request 84-inch table pricing
USPE-AT-101SFixed-height, six-leg table with integrated sink and hydro aspirator101 × 32½ × 36 inches overall; 79 × 27½-inch dissection basin.Request 101-inch table pricing

Each model is quoted for its selected configuration. A fixed-height sink table should not be specified as a rotating or elevating pedestal table simply because both are used for post-mortem examination.

Specify downdraft ventilation, rotation and utilities together.

For a rotating autopsy table, provide the room plan and service locations before choosing the installation position. The USPE-AT-PED listing describes manual rotation of 180 degrees in either direction. The rotation envelope, connected services and selected exhaust arrangement still require a coordinated layout.

Downdraft equipment needs an exhaust design matched to the model and the building. Include available airflow, duct route and the facility engineer’s requirements in your RFQ. If the project calls for self-contained exhaust or recirculating filtration, identify the requirement for review; do not assume it is included, suitable for every procedure or a substitute for required building exhaust.

Request grid plates, rinse systems, disposers, measuring accessories and other table options against the selected model. Include hot and cold water, drainage, backflow protection, power and service access in the installation schedule. A separate autopsy sink station must be checked for its intended use and interface.

Connect examination, discreet transport and storage.

A table is only one part of the route. Use a hydraulic covered cadaver carrier for discreet transport, or review the hydraulic autopsy trolley with removable top where the approved workflow requires a supported top transfer. A fixed platform and a removable tray are different configurations; do not assume they exchange between devices.

Plan the receiving mortuary lift, storage rack and mortuary cooler together. Check transfer height, load rating, tray support, door clearance and retaining arrangements at every connection. Review 23-inch, 27-inch and 30-inch stainless steel trays by the actual equipment drawing; a matching width does not establish compatibility.

A complete scope makes a useful equipment quote.

Send the table type, quantity, facility location and required working dimensions. Add a room plan when sink orientation, delivery access or utility placement matters. For custom work, identify the required characteristics separately from optional upgrades so the base equipment and alternates can be priced clearly.

  • Model and configuration: table dimensions, sink position, fixed or elevating support, tray or cover arrangement and required accessories.
  • Facility connections: available water, drainage, power and building ventilation, with the installer’s scope identified separately.
  • Procurement documents: request manufacturer, model, part number, country of origin, technical literature and dealer/OEM status for the quoted equipment.
  • Commercial details: request itemized pricing, freight, lead time and the applicable written warranty. Delivery or installation dates must be confirmed in the quote.

For staged replacements or multi-room projects, identify the first installation and later phases in the same request. We can review supporting equipment without treating future quantities as an immediate order. Include USPE stainless laboratory casework and finish options in the same project, and keep selected models together in your current USPE quote. Review financing information for payment options, subject to the provider’s terms and approval.

Autopsy table buying questions

What is the difference between an autopsy table and an autopsy trolley?

A table provides the working surface and support specified for the procedure. A trolley adds a mobile base, but its permitted uses, adjustment range and transfer arrangement depend on the model. Some have fixed tops; others have removable tops. Select by the actual model specifications rather than the name alone.

Can I request left-, right- or center-sink equipment?

Review the left-hand, right-hand and center-sink stations. Include the room plan and required connections in the RFQ. A separate sink station is not automatically a docking station for every carrier.

Can options be included in the same RFQ?

Yes. Use the configuration choices on the relevant equipment page and include quantities and project notes. Unpriced option references are requests for review, not confirmed retrofit parts. The written quote identifies approved options, included components and any changes to the base model.

How much does an autopsy table cost?

These USPE autopsy tables are quote-only. The selected base model, elevation, fixtures, ventilation and approved options determine the equipment price. Request an itemized quote rather than comparing an incomplete base price with a fully configured table.

What should an autopsy table replacement RFQ include?

Include the existing equipment model, desired quantities, required dimensions, rotation and working-height requirements, utility schedule and site access. For a phased replacement, identify the first room and later phases separately. Request technical literature, country of origin, warranty and commercial terms for each proposed model.

How do I replace equipment identified by an older model number?

Send the existing model and serial number, photographs, tray dimensions, working heights and utility details. We can review the requirement against current equipment. A legacy model reference is not proof that a new unit is dimensionally identical or that old accessories will fit.

Anatomy lab and autopsy-room handling

Plan the table, lift and tray as one transfer workflow

A dissection table is one part of the handling route. Match the tray support, transfer direction, retaining stops and working height before pairing it with a lift or rack. A roller-equipped table can support a different transfer method from a fixed recessed top or an immersion tray; rolling transfer is not a standard feature on every model.

For a complete room, include storage racks and lifts, trays and HD body boards, dissection tables and immersion equipment in the same planning request. Accessories are separate unless the accepted quotation includes them.